Two Robots Welding One Pipe Shell: When Does It Pay Off?

Table of Contents

Blog featured cover

Two Robots on One Silencer Pipe Shell: When Does a Second Welding Robot Pay Off?

By EVST Editorial Team · Reviewed by EVST Editorial Team · Last updated October 8, 2026 · Editorial policy · Corrections policy · Terms

A second welding robot pays off when one shell carries two seams that can be welded at the same time, each robot has its own clear zone, and the shell is held firmly enough that both torches stay on their seams. If the seams are very unequal in weld time, or the shell cannot be held rigidly, one robot plus more fixtures is often the cheaper answer. The cell below welds two seams on one large shell at once. This article follows what it does and then works through what has to be designed for it.

Welding large shells or pipe sections with more than one ring seam? Send us the shell drawing and your daily output and we will reply with a cell concept and a cycle-time estimate.

What the cell does, step by step

Large-diameter shells are built from sections, so one shell carries several ring seams. Welded by hand, that means climbing round the part and finishing one seam before starting the next. In this cell the work runs like this:

  1. The shell lies on its side on a roller stand. At one end, a pneumatic clamping head with blue air hoses pushes against the shell end.
  2. Two orange six-axis welding robots stand side by side behind the shell, on the same side of it.
  3. Each robot brings its wire-fed torch over the top of the shell. The left robot points at a seam at one end of the shell; the right robot points at the ring seam in the middle.
  4. The middle seam has been tack-welded first, and a row of tack points sits along it. Both torches then strike their arcs together, so two seams are welded at once.
  5. During welding, each torch stays close to its own position, the arc keeps running and spatter flies outward.
  6. Each robot carries its own wire reel on the wrist.
Shell on a roller stand with two six-axis welding robots standing behind it
The cell: the shell lies on a roller stand with a clamping head at one end, and two six-axis welding robots stand side by side behind it.
Two welding arcs burning at the same time on one shell
Both torches have struck their arcs: the left one on a seam at one end of the shell, the right one on the middle ring seam with its tack-weld points.
Close view of two torches over the shell, with a wire reel on the near robot's arm
Close view: both torches work from above the shell, and the near robot carries a wire reel on its arm.

Question one: how many seams, and where do they sit?

The second robot earns its place only if there is a second seam worth welding in the same time window. Two things decide that.

Weld time per seam. If one seam takes three times as long as the other, the second robot spends most of the cycle waiting. The best pairing is two seams of similar length and similar work, so both robots finish close together.

Reach from one side. Both robots here stand on the same side and reach over the top. That works when the seams are far enough apart for two torches and two wrists to fit between them. If the seams sit close together, the robots compete for the same space.

Situation Second robot One robot, more fixtures
Two seams of similar weld time, well apart along the shell Fits: both run together Seams run one after another
One long seam and one very short seam Second robot mostly idle Usually the better answer
Seams close together Zones overlap, hard to separate Simpler to program and guard

Question two: how is a long shell located and clamped?

On a roller stand with a clamp at one end, the shell is positioned by two things: the rollers that carry it and the head that pushes against its end. With two torches working at different positions along the shell, any shift, sag or play shows up at both seams at once, and one correction cannot fix both.

General points to check:

  • Seating of the end stop. The clamping head must push against a face that is the same every time, or the shell sits slightly differently on each cycle.
  • Roller spacing against shell length. The rollers carry the weight, so their spacing and height decide whether the shell sits level or droops between them.
  • Section-to-section fit. A shell made of butt-joined sections has a joint that is only as good as the alignment when it was tack-welded. Tack welds lock that alignment in, so what the tacking leaves behind is what the robots inherit. If the gap along the joint varies, plan for a way to see it, such as seam tracking or touch sensing, rather than hoping every shell arrives identical.

Question three: how are the work zones kept apart?

Two robots on the same side of one part are only a good idea if each one owns a defined zone. The usual approach is to give each robot its own seam and treat the space between them as shared, with a rule about who may enter it.

  • Reach and swing. Check the whole arm, the torch cable and the wrist-mounted wire reel, not just the torch tip. Bulk is what touches the neighbour.
  • Interlock. Put a keep-out region between the robots, with the controllers sharing a signal so one robot cannot enter while the other is in it. Coordinated control of both robots is another route; which one fits depends on how tightly the two programmes depend on each other.
  • Check before commissioning. Run the taught paths in offline simulation with both robots loaded, then slowly on site, before any arc is struck.

Question four: how are the start and stop points staggered?

Two arcs heat the same shell at the same time, and two ring seams each have a place where the arc starts and a place where it stops. Those places are where the weld is least uniform.

  • Do not put both stops in the same angular position. Stopping points that line up around the shell concentrate heat and any imperfection in one region.
  • Offset the starts. If the two arcs start at different angular positions, one robot’s start does not coincide with the other’s stop, and the heat is spread more evenly.
  • Aim for similar arc-on time. If one seam is shorter, its robot finishes early and waits.
  • How the full circumference is covered. Whatever way the seams are reached all the way round, it is part of the cell concept and has to be settled from your shell drawing before the stagger can be planned.

When one robot plus more fixtures is the better answer

Choose one robot when output is modest, the seams are close together, one seam dominates the weld time, or the shell range is wide and each variant needs its own set-up. A second robot adds a second wrist, cable run, reel and set of teach points to look after, so it only makes sense if the time saved is used.

Short answers to common questions

Do two robots halve the welding time? Only when both seams take similar time and neither robot waits for the other. Loading, clamping and unloading are separate from arc time and do not halve.

Do we need seam tracking? It depends on how consistent the joint is after tacking and how repeatable the shell location is. We decide from your drawing and how much your shells vary.

What to send us

  • A shell drawing showing length, diameter, how the sections join and where the seams sit
  • Your daily output, and how many shell variants you run
  • How the sections are tack-welded or held today

Send these through our contact page or by email to [email protected], and we will come back with a cell concept and a cycle-time estimate.

This article describes the cell shown and general design practice; it states no shell material, wall thickness, welding parameters, seam quality or cycle time.

Awesome! Share to:

EVS TECH CO., LTD
Privacy Overview

This website uses cookies so that we can provide you with the best user experience possible. Cookie information is stored in your browser and performs functions such as recognising you when you return to our website and helping our team to understand which sections of the website you find most interesting and useful.