Robot Cutting Openings in Formed Boxes: Specify the Tool Sequence Alongside the Path

Table of Contents

Robot Cutting Openings in Formed Boxes: Specify the Tool Sequence Alongside the Path

Our integration scope for a formed-box cutting cell separates the robot route, the cutting head and process controls, the fixture references and the handling of separated material. For openings on different faces, all of them affect whether the task can be completed and repeated. We define those interfaces before treating a demonstrated contour as a complete equipment proposal.

Watch the top and side operations

The footage shows a clamped metal box, a long tool carried by a white arm, a top-plane rectangular cutting contour and a later side circular contour, with bright light and sparks at the working point.

The metal box is held in a clamping structure, showing the relationship between its top and side faces.

Main film 00:01 — The metal box is held in a clamping structure, showing the relationship between its top and side faces.

Which references put the openings in the right place?

We start with the features that locate the formed box and the relationships the finished openings must have to them. The fixture locates the part; the robot’s tool frame describes the working tool. Both relationships need to remain consistent when the task moves from the top to the side.

If the proposal uses one setup, we model the complete tool against the clamps and the box on each face. If it needs re-clamping, we define how the part reference is re-established and how that affects inspection. The steel-section datum review gives another application example of why nominal geometry and the actual part reference must be considered separately.

What controls cutting before the robot moves to another face?

The quotation should identify the selected process, head, power equipment and any height-control function. We integrate their start, completion and fault conditions with the robot route. Two possible equipment branches illustrate why these are separate tasks.

For a plasma configuration with cutting-state feedback, we program the clearance approach, process start and piercing, contour, cutting finish and transition back to clearance as distinct steps. At the finish, we remove the start request, set the power command to zero and confirm that cutting feedback is inactive before the next motion. The exact commands follow the selected system’s definitions.

For a selected laser package with capacitive height following, we treat calibration, following and the retract-to-park action as head functions. We define how these functions and their permitted operating conditions connect to the robot’s approach and face transition. Robot teaching and head commissioning are therefore different items in the integration scope.

The tool works near a rectangular contour on the top face, with bright light and sparks at the working point.

Main film 00:13 — The tool works near a rectangular contour on the top face, with bright light and sparks at the working point.

What happens after an interruption or when material separates?

We identify which material is the retained product and which is the cut-out. That affects support, collection and the recovery plan. A released piece must have a defined place to go, with its interaction with the tool, fixture and box interior included in the trial.

Restart also needs a process decision. For a plasma configuration that supports interrupted-position recovery, we save that position, remove the start request and define the restart arrangement. The restart position depends on the finished side and the permitted mark or damage zone. Cutting a circular opening and recovering a round piece need not use the same recovery route.

We therefore include a stopped-and-restarted sample where recovery matters. It should show the permitted approach, process re-entry and effect on the retained feature, rather than simply resuming robot motion at an arbitrary point.

Later, the tool is near a circular contour on the side face, showing its relationship to the box after the face transition.

Main film 00:34 — Later, the tool is near a circular contour on the side face, showing its relationship to the box after the face transition.

What should the cutting trial deliver?

Trial output What we use it to settle
Formed samples with the agreed locating references How the real box is presented to the tool
Top and side routes, including starts, finishes and transitions The robot and cutting-head sequence for the required faces
A defined cut-out and recovery arrangement Where separated material goes and how a stopped part is handled
Feature measurements and edge inspection against the drawing Whether size, location and the next operation’s edge requirements are satisfied

We agree the required dimensions and edge condition before the run, and use the same references for inspection. If a finishing operation is needed after cutting, it remains visible in the proposal rather than being hidden behind the contour demonstration.

Send EVST top and side photographs or a formed-box drawing, marked opening references, existing clamp photographs and the required edge/assembly conditions. Also say whether the round material is waste or a required product. We can use those inputs to develop the fixture-access, cutting-system interface and sample-recovery scope. Discuss multi-face box cutting integration.

Awesome! Share to:

EVS TECH CO., LTD
Privacy Overview

This website uses cookies so that we can provide you with the best user experience possible. Cookie information is stored in your browser and performs functions such as recognising you when you return to our website and helping our team to understand which sections of the website you find most interesting and useful.