
Robot Knife Cutting for Shoe Soles and Insoles: When Does It Beat Press Dies?
By EVST Editorial Team · Reviewed by EVST Editorial Team · Last updated September 30, 2026 · Editorial policy · Corrections policy · Terms
Robot knife cutting beats press dies for shoe soles and insoles when you run many sizes and styles in short batches. The outline is a program, not a steel die, so a new size means a new cutting path instead of a new tool. Press dies stay ahead when one outline runs in long batches and a single stroke per part matters more than flexibility. In the cell described here, a robot with a pneumatic knife unit cuts a sole out of a flat sheet by following its outline.
Cutting soles, insoles or other soft sheet parts? Send us your part drawing and daily output, and we will reply with a cell concept and a cycle-time estimate.
Die per size or programmed outline
Soles and insoles are usually cut on a press with a cutting die, by hand, or with a knife carried along the outline. Hand cutting needs no tooling, but it is slow and the edge varies from part to part. The real choice is between the press and a programmed knife.
| Question | Press with cutting dies | Robot with a knife unit |
|---|---|---|
| Tooling for each size | One die per size, and usually a mirrored die for the other foot | One cutting path per outline; the mirrored foot is a program change |
| New style or sample | The die has to be made before the first part | The path comes from the outline drawing |
| Changeover | Swap and position the die | Load another program |
| Time per part | The whole outline in one stroke | The blade travels the full outline, so time grows with outline length |
| Best fit | Few outlines, long batches | Many sizes and styles, samples, short batches |
The rule is simple: count your outlines and how many parts each one runs before it changes. The more outlines and the shorter the runs, the more die cost and lead time work against the press.
What the cell does, step by step
- The sheet lies flat. A grey, textured sheet of sole material is laid flat on a metal table.
- The blade goes in. The robot brings the pneumatic knife unit over the sheet, and the blade presses down into the material.
- The robot follows the outline. The robot carries the knife along the sole outline and turns the blade direction as it goes.
- The shape is closed. When the outline is complete, the blade lifts and the robot moves clear of the table.
- The sole comes out. The sheet is lifted by hand and the cut sole is taken out, leaving a sole-shaped opening in the sheet. The sole and the sheet end up side by side.


Everything that decides whether this cycle gives a clean part happens at three points: before the blade goes in, on the curves, and after the blade lifts.
Holding a soft sheet while the knife drags through it
A die comes down on the whole outline at once and pins the material while it cuts. A knife pushes in at one point and drags along the path, pulling the sheet sideways the whole time. If the sheet lifts, creeps or ripples, the outline is cut in the wrong place, or the blade rides up and does not cut through.
For soft sheet, the hold-down is decided by three things:
- How the sheet is held. Common options are a vacuum table, a clamping frame around the sheet, or hold-down strips along the edges. Soft, thick sheet generally needs more hold-down than thin, stiff sheet, and a textured surface can leak on a vacuum table.
- What sits under the cut. The blade has to pass fully through the sheet, so the surface underneath must tolerate the tip without dulling it or being cut up. A replaceable underlay is the usual answer.
- Where the sheet is placed. If sheets are placed by hand, a corner stop or marked edge keeps each sheet in the same place relative to the programmed outline.
Turning the blade through heel, waist and toe
A sole outline is mostly curves: a round heel, a narrow waist and a tight toe. The blade has to point along the path at every moment. If it lags, it cuts partly sideways and leaves a torn or stepped edge.

The questions to settle at design stage:
- How the blade turns. It can be turned by the robot’s wrist or by a separate rotary axis in the knife unit. Either way, check that it can keep up on the tightest radius of the smallest size.
- Speed on tight curves. Slowing down on the toe and heel and running faster on the straighter sides usually gives a cleaner edge than one speed for the whole outline.
- Where the cut starts and ends. Starting on a gentle stretch rather than at the toe, and closing the outline with a small overlap, helps the part release completely instead of hanging on a thin uncut strip.
Clearing the table: parts, scrap and the next sheet
In this cell, once the robot moves clear, the sheet is lifted by hand and the sole is taken out. In production that step often sets the real output: the robot can only start the next sheet when the table is clear.
Separation depends on a few design choices:
- Nesting. Several outlines can be placed on one sheet to use material better. The closer the outlines sit, the more the hold-down and a complete cut-through matter, because neighbouring parts support each other less.
- Who takes the parts out. A person can unload one table while the robot cuts on a second one, or the robot can pick the parts with a vacuum gripper, or sheets can move through on a conveyor.
- Scrap handling. The leftover sheet with its openings is bulky. Plan where it goes so it does not slow the next load.

Where robot knife cutting fits, and where to keep the die
Robot knife cutting fits well when you cut many sizes and styles, make frequent samples or development pairs, run short batches per size, and already have the outlines as drawings.
Keep the press and dies when one outline runs in long batches, when output per stroke is the main target, or when the material is too hard or too thick for a clean knife cut, which a trial cut will show. Running both is also common: dies for the high-volume sizes, a programmed knife for the rest.
FAQ
Can the same cell cut insoles as well as soles?
If the material comes as a sheet the blade can cut and the outline is available as a drawing, a new part is a new program. Thickness and hardness still need a trial cut.
Does changing size need new tooling?
No die is needed. Each size needs its own path, generated from the outline. The blade and hold-down usually stay the same unless the sheet thickness changes a lot.
What to send for an evaluation
- Sole or insole outlines for each size, as drawings or outline files
- Sheet thickness range and a description of the material
- Sheet size and how many outlines you want per sheet
- Number of sizes and styles, and daily output per size
- How sheets arrive at the station and where parts and scrap go
Send your outlines and daily output or email [email protected]. We will reply with a cell concept and a cycle-time estimate.
This article describes the knife-cutting cell shown in the video; cycle time and cut quality depend on your material and outlines and must be confirmed in a trial cut.