Machine Tending Worm Gear Housings: One Robot, a Drawer Cart and a Machining Center
By EVST Editorial Team · Reviewed by EVST Editorial Team · · Method: on-site footage of this cell for the process loop; general engineering practice for the design decisions · Editorial policy · Corrections policy · Terms
In short: In this cell, one six-axis robot loads and unloads a machining center that mills worm gear housings. Raw castings arrive in a multi-layer drawer cart, the robot picks them one at a time, stages each part on a transfer table, and loads a two-station fixture inside the machine. The operator’s job is to refill the cart, lock it in place and start the cycle. Three decisions make or break a layout like this: how the cart is located, how the gripper and the fixture share the housing’s datums, and whether a transfer station is needed. Planning a similar cell? Send us your part drawing.

At a glance
| Part | Worm gear housing (cast, box-type) |
| Process | Milling on a machining center |
| Automation | Machine loading and unloading by one six-axis robot |
| Part supply | Multi-layer drawer cart, pushed in by the operator |
| Cart location | Toggle clamp plus locating pin |
| Workholding | Two-station fixture on a rotary unit, two parts per load |
| Buffer | Transfer table beside the machine |
| Operator role | Refill the cart, lock it, start the cycle |
The problem this cell addresses
Box-type parts such as gearbox and worm gear housings tend to have long machining times per part. When every machining center needs someone standing by to clamp and unclamp, either the operator waits for the machine or the machine waits for the operator. Moving the loading job to a robot, and batching the operator’s work into cart refills, is the usual way out.
How the cell runs
- Refill. The operator loads raw castings layer by layer into a drawer-type cart and pushes the cart to the robot.
- Lock and locate. A toggle clamp locks the cart; a locating pin sets its position.
- Start. The operator starts the cycle from the touchscreen.
- Pick. The robot takes parts from the cart trays one at a time with a pneumatic gripper that closes on the housing’s outer shape.
- Stage. Each part goes to a transfer table beside the machine first.
- Load and machine. The robot places parts into a two-station fixture on a rotary unit inside the machine — two parts per load — and the door closes for milling.
- Unload. After machining, the robot removes the finished part and the next loop begins.

Three design decisions
1. Locate the cart the same way every time
The robot picks from fixed positions. If the cart stops a few millimeters off, every part on every tray is off by the same amount. This cell uses two separate features for that: the toggle clamp holds the cart, and the locating pin sets where it sits.
When we specify a drawer cart, four things get settled before anything else: whether the robot can reach every position on every layer, how accurate each pick position has to be, how the cart is locked, and how the drawers open and close. Standard furniture-grade slides are not built for this duty; drawers that the robot picks from thousands of times need precision slides with little play.
Question to settle early: how long should one cart run before a refill? That interval sets how often the operator comes back and how many layers the cart needs.

2. Design the gripper and the fixture around the same datums

Box-type parts on a machining center are usually located with the one-face-two-holes method: the bottom face as the primary datum, then a cylindrical pin and a diamond (relieved) pin for the remaining degrees of freedom. Clamping is best linked, so the force is even and thin walls do not distort; in an automated cell that clamping is pneumatic or hydraulic.
For robot loading, that means two things have to agree:
- Where the gripper holds the part. It must not cover the fixture’s locating face or pins, and the part has to settle onto them when released.
- How the tray presents the part. Ideally the tray orientation already matches what the fixture needs; otherwise an extra reorientation step is needed.
A self-centering gripper tolerates small pick-position offsets; a two-finger gripper needs a more accurate tray.

3. Decide whether you need a transfer station

This cell stages each part on a transfer table before loading. Whether you need one comes down to two questions:
- Does the orientation on the tray match the orientation the fixture needs?
- Can the robot hold a raw part and a finished part at the same time, so it can swap them at the machine door?
If the orientations differ or the gripper holds only one part, a transfer position earns its place. If not, it can often be left out, which shortens the loop.
When this layout fits — and when to look closer
- Good fit: stable batch production, long machining time per part, and castings or housings that can sit on a tray in a fixed orientation.
- Evaluate further: frequent changeovers (can trays, gripper and fixture be shared across part numbers?), inconsistent raw-casting dimensions (they affect picking and locating), or parts that must be flipped between operations.
FAQ
How many parts does a drawer cart hold?
Work backwards from the refill interval. Multiply parts per hour by the hours you want between refills; that is the cart capacity. Then check how many parts fit per layer with gripper clearance, and how many layers the robot can reach.
What gripper suits cast housings?
One that grips surfaces the fixture does not need. A self-centering gripper is more forgiving of tray position; a two-finger gripper needs tighter tray accuracy.
Is a transfer station always needed?
No. It is useful when the tray orientation differs from the fixture orientation, or when the gripper cannot hold a raw and a finished part at once.
Get a layout and cycle-time estimate
Send us:
- Part drawing with datums and clamping faces marked
- Raw part condition (casting, forging, pre-machined) and dimensional consistency
- Annual or daily volume, shifts, and the refill interval you want
- Machine model, door type and current fixture
- Photos or dimensions of the floor space
We will reply with a cell layout proposal and a cycle-time estimate.
Send your part drawing → or email [email protected]
Footage filmed at a partner’s production site. Cycle time and accuracy figures from that site are not public and are not given here.